Home Articles Downloads Forum Products Services EBME Expo Contact ☰

Register Log In

EBME Forums Forums Maintenance Technical Assistance force fx error 160

Print Thread

Rate Thread

force fx error 160 #64992 08/06/13 9:40 AM
Joined: Apr 2005 Posts: 371 Karachi Laiq OP Sage
OP Laiq Sage Joined: Apr 2005 Posts: 371 Karachi	Dear all. I am facing error 160 in force fx-8c. all fets, diodes & power mosfet ok. Any help will b appreciated. thanks in adv. Laiq

Re: force fx error 160 Laiq #64993 08/06/13 11:18 AM
Joined: Feb 2004 Posts: 14,662 Likes: 62 the path less trodden Geoff Hannis Super Hero
Geoff Hannis Super Hero Joined: Feb 2004 Posts: 14,662 Likes: 62 the path less trodden	Can we assume that you have the manual, my friend? It talks a lot about ECON. If you don't inspect ... don't expect.

Re: force fx error 160 Laiq #64994 08/06/13 7:40 PM
Joined: Apr 2005 Posts: 371 Karachi Laiq OP Sage
OP Laiq Sage Joined: Apr 2005 Posts: 371 Karachi	Yup i have it

Re: force fx error 160 Laiq #65002 11/06/13 11:31 AM
Joined: Sep 2009 Posts: 132 Vietnam hieu Expert
hieu Expert Joined: Sep 2009 Posts: 132 Vietnam	Hi Laiq. I have service manual schematic diagrams for this machine. I will share it to you if you need. Please contact me via email: Hieuvthospital@gmail.com

Re: force fx error 160 Laiq #65039 13/06/13 1:00 PM
Joined: Aug 2007 Posts: 306 carlisle uk bcarlisle Master
bcarlisle Master Joined: Aug 2007 Posts: 306 carlisle uk	Book says Calibrate ECON factor. Refer to section 5-34. If alarm reappears, refer to correcting T_ON ASIC Malfunctions. (6-19), which refers to seating IC U9 on the control board, fails again after all this change the U9 chip (Programmable IC) Hope this helps

Re: force fx error 160 Laiq #65069 15/06/13 3:50 PM
Joined: Apr 2005 Posts: 371 Karachi Laiq OP Sage
OP Laiq Sage Joined: Apr 2005 Posts: 371 Karachi	Dear All I have tried removing battery. Machine Still showing Error160. I have replaced other working control board. There was no Error, it booted normally. I shorted C10 after that now machine showing Error160 & Error212. I will try to calibrate again. But it means there is problem in Control board. Any guidance or help. where to look.

Re: force fx error 160 Laiq #65622 11/08/13 9:07 AM
Joined: Apr 2007 Posts: 3 nepal shyam shrestha Newbie
shyam shrestha Newbie Joined: Apr 2007 Posts: 3 nepal	Please check rectifier of FET PCB, replace if faulty then calibrate ECON factor as per manual. shyam

Moderated by DaveC in Oz, RoJo

Link Copied to Clipboard

Who's Online Now

0 members (), 428 guests, and 17 robots.

Key: Admin, Global Mod, Mod

Yousri, mosfet1996, rajvenugopal, Arzo Momand, steve_shomz
10,180 Registered Users

Forum Statistics

Forums25

Topics11,064

Posts73,734

Members10,180

Most Online5,980
Jan 29th, 2020

Powered by UBB.threads™ PHP Forum Software 7.7.5